POSITIVE-NEGATIVE-CONNECTIONS

BMW E46 Angel Eye Install

Required tools

  • Phillips Screw Driver (corner lamps)
  • Flat Head Screw Driver (optional for headlight cover)
  • T25 Torx Bit (for the ECU box cover)
  • Zip Ties (always)

You are essentially removing your headlights, including your corner lights.  Open up the headlights, install our rings, close the headlights, put the assemblies back in, and optionally hooking the wires up to your ECU.

Step 1: Remove corner light

If you have a ‘push in’ corner light, your uninstall will be done like the image depicts, by pushing down from the hole on top of your fender, and pulling slightly and carefully and slide it out.  If you have a ‘screw in’ corner, you will remove it by inserting a Phillips screw driver into the same hole, into the same position, and unscrewing it, sliding it out after.

Step 2: Remove the rubber trim outlining your headlight

Push down on the back sides of the pointed out areas, there is also one more close to the center of the car, at the bottom corner of the headlight.  Once removed, you will see the next step.

Step 3:  Remove lower painted trim

Start from the side nearest to the center of the car, as that is the most difficult ‘side’ to pull off first.  The slide in clips to the fender slide out easily.

Follow the top picture to remove from the fender side, it is 4/10 difficult for your first time doing it, the lower pictures is a reference of how it is connected to the fender, so you can picture it in your head when you are removing that side.  It’s kind of hooked in, but be gentle.

Step 4: Remove headlight assembly from vehicle

Pointed out above are the screws to remove, the first image is the front view, the second is the rear view.

Once you have the screws removed, gently slide the headlight assembly forward, just an inch or two, so you have more room to grab and disconnect all connectors.

Step 5: Slide the headlights out

Step 6: Remove plastic lens

Remove the plastic lens from the front of the housing by lifting up all of the tabs surrounding it, it slides off directly forward once the tabs are lifted.

Step 7: Install Angel Eyes

Once you have open access to your housing, insert the clips on the ring, and apply the rings to clip onto the top part of the projector/reflector housing as shown below.

Route the wires to the back side of the housing, through the rubber grommet.  When you look inside of the headlights from the front, you will see there is a hole across the top of the inner housing for you to push the wires through.

Step 8:Harness

The harness will need to be connected to your ECU, so remove the cover to your ECU located near the drivers side windshield corner of your engine bay.

Tap this wire, it is in the same spot for all E46 body.

You will have to route this part of the harness to the opposite side (passenger side) to connect to the positive and negative terminals.

Use the above graphic for reference on what connections to make.


Once you reverse the steps and put everything back into place, you’re done! Enjoy your new LED Angel Eyes!

Angel Eye Guide (fastm.com version)

Here is another install guide from the epic and famed fastm.com website (Kevin), we copied it here directly from this page: http://www.fastm.com/m3/angeleyes_orionv2.html so feel free to head over there for images and possibly more information

Installation

Install Time: (anywhere from 30-90min., if you had to do it a second time it will be much quicker)

Before you begin:

a) Inspect and test your kit prior to installing. If anything is not working, best to get it replaced before taking your headlights apart.

b) Pop open your hood.

c) Get lots of water if you dehydrate fast. 🙂


Pre-Install: Testing the Angel Eyes

  1. Unravel the wire harness and lay it out so you can easily find all the terminal connectors. Refer to this image for all the terminals.
    Click Here.
  2. Locate the Brown and Red wires that has the bullet style male/female terminals.
  3. Connect the brown wire from the Angel Eyes to the brown wire on the harness.
  4. Connect the white wire from the Angel Eyes to the red wire on the harness.
  5. Repeat c & d for the other set of Angel Eyes.
  6. Open the hood of your car and visually locate the ground post and the positive post.
  7. Locate the ground wire on the harness and hold it to the ground terminal on your vehicle.
  8. Locate the red (+) wire on the harness and hold it to the positive battery terminal.
  9. Locate the brown trigger wire on the harness and touch it to the positive battery terminal to trigger the relay to turn the Angel Eyes ON/OFF.
  10. Your Angel Eyes should turn on and bring a smile to your face.

Installation

Step 1. Headlight lense removal

(Driver’s side shown, Passenger side similar)

1a) Remove the turn signal corner lamp. Use a Philips Screw Driver to loosen the retaining screw as pictured below. The screw does not come out so
don’t keep turning or you’ll be turning forever. Once loosen, slide the corner lamp forward and undo the bulb connector. Set the lamp aside.

image image

1b) Remove the rubber trim surrounding the top/side of your headlight. You can easily undo the top 3 tabs with your fingers by lifting the tabs from behind.
The two tabs on side might be easier with a flat head screw driver.

image image

1c) Remove the lower painted headlight trim. If you have the cold weather package with the headlight washer like I do, it will be easier if you did not remove
the entire trim. Start by unlatching the trim from the end closest to the grill then the latch that is visible from where the corner lamp was removed. To unlatch you
simply reach from behind and unhook it similar to how your removed the rubber trim. If you have the headlight washer, you do not need to disconnect it, just tilt the
trim piece out as far as you can. That should give you enough clearance. If you do not have the headlight washer it’s up to you if you want to remove it entirely or
just tilt it out.

image

1d) Remove the clear headlight cover lense. Tools aren’t really necessary here. There are three plastic tabs on top, one on the side, and three on the bottom
that must be unlatched. Carefully pull up on each tab till it releases from lense. As you work your way around each tab you should be able to remove the lense by sliding
it out.

image image

1e) Remove the OEM inner trim bezel. The bezel simply pulls straight out. No tools needed.

image

1f) Repeat the above steps on the passenger headlight.


Step 2) Mounting Angel Eyes Rings

2a) Mount the Angel Eye Ring to the DRL (Day Time Running Lights, also called High Beam Flasher). At the top of the reflector is a lip. Simply slide the alligator
clip at the top of the Angel Eyes onto the top of the reflector lip. See image below for proper spacing of the clips. You do not push both clips all the way in, only
the inner clip (closest to grill) is pushed all the way while the other clip (closest to the Bi-Xenon projector) has some spacing. The easiest way to do this is to
slide both clips in till the ring lines up with the outside of the reflector. Now look over the Angel Eye ring to make sure it’s even all the way around and lined up.
Take a view from the front and make sure the sides are even and the ring is centered. If not shift it to the left or right to center it.

image

2b) Mount the Angel Eye Ring to the Bi-Xenon projector. The same process applies to ring for the headlights. Push the clips in till the ring lines up. Simply
push it till it gets within 1-2mm from the top of the projector housing. The ring should be completely vertical when looking at it from the side. See image below for
the correct and incorrect way to installing it.

image
image

2c) (Optional) Remove the intake duct from the air box. This will provide additional room to work behind the driver’s
headlight.

image

2d) Remove the H7 bulb from (flasher) socket and peel the rubber boot back. Surrounding the H7 bulb socket is a rubber boot. Peel back on the boot from the
top to allow you to pass the Angel Eye wires through.

image

2e) Feed the Angel Eye wires from the front (above the reflector) to the back through the rubber boot. First unplug the four connectors from the wire harness.
Second, to aid in the process, a thin copper wire will help you pull the wires through. Feed the thin copper wire through from the front to the back and through the
boot opening. Wrap the wire around the Angel Eye wires and tape it down with electrical tape. Now pull it through from the boot side (back of headlight). Note, example
images below are from a previous install, however the process is the same for the Orion V2.

image image

2f) (Optional, not recommended, skip to step 2g) Make a small incision on the rubber boot with a small pocket knife and feed
wires through boot.
This will allow you to pass the wires through the boot and also allow you to reinstall the boot around the socket opening without any gaps.
Using needle nose pliers, grab one of the Angel Eye wires by the terminal and stick it through the boot opening that you made in the previous step. Then on the other
side of the boot, use your needle nose pliers again to pull the wire through. Do this for the other 3 wires till all four wires are through. Note, example images below
are from a previous install using the umnitza Predator Chromium, however the process is the same for the Orion V2. If you used this method, then skip to step 2h.

image image

2g) (Only if you skipped step 2f) Bend wires around housing. Bend the wires around the headlight housing on the flat part
of the bezel, not the raised part where the boot latches on to. (See image below).

image

2h) Connect wires and close the rubber boot. Since the wires come preinstalled with connectors, you can’t get this wrong. Plug each of the four connectors
to the harness.

(Optional: I used some 3M double sided tape to secure it to the back of the headlight. I also used electrical tape around the connector
and wire loomed everything to give it a factory-like appearance. You can now reposition the boot and reinstall it.)
You can now reinstall the H7 bulb.

image

2i) Repeat the above steps on the passenger headlight.


Step 3) Wire Harness Installation

3a) Lay the wire harness on top of the engine bay. The relay should be near the passenger side positive (+) battery terminal. See image below for the
correct positive terminal. The shorter end of the harness coming from the relay should follow the passenger fender to the passenger headlight. The longer end should
go across the engine to the driver’s side fender towards the driver’s side headlight.

image

3b) Ground the relay. Use a 10mm socket to remove the 10mm nut located in the passenger power terminal area. Mount your relay and ground here. The
ground wire is the short black wire coming out of the relay with a ring terminal at the end of it. See picture below.

(NOTE: For a better ground, you should utilize the factory 19mm ground terminal as pictured in the previous step 3a)

image

3c) Route the short harness to the passenger side headlight. If you lift the weather stripping from the passenger side power terminal area, you can slide
the harness under the factory harness bundle then route it down the passenger fender to the passenger headlight.

image

3d) Connect the passenger side angel eye harness to the relay harness.

(Optional: Soldering the connection along with use of heat shrink tubing will provide a permanent and secure connection.)

3e) Route the long harness across the top of the engine and secure it over the OEM wire holder. See pictures below.

image

3f) Route the long harness through to the brake fluid / ECU box area then down the drivers side fender. I chose to go through the OEM weather stripping as
pictured below. Leave the trigger wire in the ECU box area for now and run the harness down the drivers fender (being as neat as possible).

image image

3g) Connect the driver’s side angel eyes harness to the relay harness. After running the harness down the driver’s side, connect it to the Angel Eyes.

(Optional: Soldering the connection along with use of heat shrink tubing will provide a permanent and secure connection.)

image

3h) Connect the red wire from the relay to the positive (+) terminal found in the power terminal area.

(NOTE: If you have the OEM Navigation, make sure it is completely turned off and not on before beginning. There is a chance that your navigation
can become damaged if you pull the power when it is powered on.)

First you must locate the OEM hood switch and unplug the connector. Next lift the weather stripping out of the way then lift the cover up by grabbing under where
the positive terminal is. See first picture below. Use a 13mm socket to remove the 13mm nut from the positive terminal. Locate the red wire (with an inline fuse)
coming out of the relay and mount it on the positive terminal. I chose to install the red wire underneath the OEM battery cable. Do the reverse to put it all back together
then zip tie any lose cables. TIP: If you zip tie the inline fuse holder to the relay as pictured below (3rd pic on the right) you’ll have easy access to the fuse).

image image
image

3i) You are now ready to test your Angel Eyes. Coming off the relay should be a second trigger wire that is brown. Have someone touch the brown wire to the
positive terminal or use a clamp then examine if your Angel Eyes work. If all is good, remove the brown wire from the positive terminal.


Step 4) Trigger Wire Installation

(To ECU Accessories wire for “Always On” method)

Note: The Accessories wire method is one of many ways to wire the Angel Eyes. This method will allow you to have the Angel Eyes on all the time whenever the
car is running. This is independent of whether your headlights/parking lights are on or off. When you turn off your car, the Angel Eyes will stay on for a few seconds
since there is still power through the accessories wire. This will not cause any power drain issues as the Angel Eyes do not draw a lot of power. Skip this step
if you do not want the Angel Eyes on all the time.
You can search the forums such as m3forum.com for other wiring methods.

4a) Open the cover to the ECU box using a Torx 25 bit to remove four Torx head screws. (Note: Some earlier cars might be HEX 27). Once the screws are
removed, tilt the cover up and pull out.

image

4b) Locate the red wire with white stripe and yellow/gold tracers. Install your blue wire tap using your pliers. Make sure you center the wire tap, then squeeze
down using your pliers. Do not sever the wire, DO NOT cut any wires, and DO NOT yank on any other wires. Be careful. 🙂

(Optional: Soldering the connection along with use of heat shrink tubing will provide a permanent and secure connection.)

image image

4c) Route the red trigger wire into the ECU box and connect the terminal end to the blue wire tap. I chose to lift one of the rubber grommets and lay the
red trigger wire underneath. You can fish it through the grommet if you like for a more professional look.

image

4d) Test the Angel Eyes by turning your ignition to position 2. If your Angel Eyes light up then you are good to go and you can begin cleaning up the loose
ends.

4e) Reinstall the ECU box cover at this point if your Angel Eyes are working ok.


Step 5) Clean Up

5a) Tape the 2nd Trigger wire. If you are not using the second trigger wire (wire closest to relay), you should tape it using electrical tape and tuck it
away. Make sure to tape up the connector end so that it doesn’t accidentally get in contact with the frame of the car.

5b) Zip tie the harness. Using zip ties, secure the harness down along the fender, etc. Make sure no wires come in direct contact with the engine.

5c) (Optional, assuming you made a slit on the rubber boot from steps 2f) Use silicone or liquid electrical tape over the
incision area on the rubber boot where the Angel Eye wires were installed.
This should prevent any moisture from possibly getting into your headlights.

5d) With the lense still off the headlights, check the Angel Eyes to make sure they are still aligned and in the proper position.

5e) Reinstall your headlight inner bezel. When reinstalling the headlight bezel, pay attention to the outter ring of your Angel Eyes. If you see the top is
compressing the Angel Eye ring, you might need to move the Angel Eye ring further back. If you can not adjust the ring any further, you can leave the outer corners
of the bezel loose. (i.e. do not snap it in place). If you snap it in place it will push the Angel Eye ring too close to your projector housing and possibly interfere
with the self leveling adjustments or rub off the chrome on the surface of the projector. It will be fine to leave these two corners loose.

5f) Reinstall your headlight lense and trim following the reverse procedures you following for removal.

5g) Using some wire loom, dress up the wires coming from the back of the headlights, the wires from the angel eyes, etc.

image

19 thoughts on “BMW E46 Angel Eye Install

    1. lAnthony

      I helped my grandson finish wiring the CCFL Angel Eye Halo lights in his recently purchased 2003 BMW 325 I. The previous owner did not complete the installation and did not use the proper relay to enable the Angel Eyes to be controlled from the interior lights. I created a schematic for the wiring because I could not find one anywhere. A single pole double throw relay is required with the normally closed contact connected to the interior light circuit. I would like to send the schematic to you so you could include it in your post. Please contact me via my e-mail address and I will send the schematic and the writeup to you. I wrote this up to teach my 17 year old grandson how it works. Thank you for a terrific post. It helped a lot.
      Anthony

  1. Jason McClary

    Quick question, how do i install it so it can turn on when ever I hit the key entry button on my key. I’ve seen some people have it to turn on like this and stay on while car is on and then shut off when car is off and the illumination of lights goes off inside car. I like that better. Can you help me with instructions on this.

    Thanks in advance

    Jason

    Reply
    1. [email protected] Post author

      we have it explained in this guide, it is the ECU wire tap near your computer closest to the windshield under the hood! the wire you tap into is the interior light signal wire

  2. steve

    Hi i have just installed an aftermarket angel eye headlights and i have a question, the halo rings only come on for the day light running lights and i want them to stay on all the time even with my hid xenon lights how can i do it? is it just a simple re wiring or what do i do?

    Reply
  3. Sean

    Ah, not all E46s are created equal… I have a European model made for the Thailand market. Got into my ECU box and found there is no accessory wire to be found. 🙁 I spent an hour with the wife turning the key on and off, and alas, nothing suitable.

    In the end I made a compromise and tapped the front park light. I already ran the long trigger wire into the ECU box and labelled it so next time she’s in for a service I’ll ask the locals to find me an accessory wire, or run one for me.

    Otherwise, it’s looking great and working well. Since the law in Thailand doesn’t require DRLs, maybe I’ll leave it this way.

    Reply
  4. Rob From Canada

    Perfect installation first time. Great instructions and accompanying pictures. Super fast shipping all the way north of the border and they worked first time. Thanks for putting up the detailed notes. Made for an easy install.

    Cheers….

    Rob

    Reply
  5. Ryan

    Love the lights except the smaller ones don’t get as flush as the larger one on the set. I felt instructions could be better as some of the wires don’t even match the ones you sent me on my harness . So it was some guessing. They do look amazing and I can’t wait till tonight to see the full effect.

    Reply
    1. Daniel

      Mine are very dull, are they supposed to be almost unnoticeable and if not what are some reasons for this?

  6. Pingback: Angel Eyes too bright.

  7. Braiden

    I noticed the facelift coupes do not have a clip system with them. What do you guys recommend for install? I’ve searched all over forums, but haven’t found a forum that mentioned this issue, unfortunately.

    Reply

Leave a Reply

Your email address will not be published. Required fields are marked *